Arizona Palm

Many Different types of palms grow in Arizona

Meter Ppm

December 31st, 2008

Rick

Meter Ppm

HM Digital TDS-EZ Meter/Tester, Water/ppm/Purity/Filter

$15.98

Factory Calibrated: our meters are calibrated with a 342 ppm NaCl solution. Meters can be recalibrated with a mini-screwdriver. Fun, translucent blue housing that’s very strong and durable.
Includes a TDS chart sticker on the back of the meter that explains TDS values.

Measurement Range: 0-9990 ppm. From 0-999 ppm, the resolution is in increments of 1ppm. From 1000 to 9990 ppm, the resolution i…

TDS Calibration Solution (One Bottle 90ml)

$6.75

For use with the HM Digital TDS-EZ, TDS3 & TDS4 Testers or any Tds Tester that requires an NaCl calibration solution…

HM Digital TDS-EZ Meter Tester Water/ppm/Purity/Filter

$18.95

Measurement Range: 0-9990 ppm. From 0-999 ppm, the resolution is in increments of 1ppm. From 1000 to 9990 ppm, the resolution is in increments of 10ppm, indicated by a blinking ‘x10′ image.

Factory Calibrated: our meters are calibrated with a 342 ppm NaCl solution. Meters can be recalibrated with a mini-screwdriver.

Fun, translucent blue housing that’s very strong and durable.

Includes a TDS ch…

Milwaukee Instruments SM802 pH/EC/TDS Combined Meter, Range: 0.00 14.00 pH, 0.00 6.00 mS/cm,0 4000 ppm

$199.99

Smart 3-in-1 portable meter1 probe for pH, conductivity and TDS Automatic Temperature Compensation Large and easy to read displayRange0.00 – 14.00 pH 0.00 – 6.00 mS/cm 0 – 4000 ppm Resolution0.10 pH 0.01 µS/cm 10 ppm Accuracy± 0.20 pH 2% full scale 2% full scale TDS ratio0.68CalibrationManual 1 pointTemp. CompensationAutomatic 0 – 50°CElectrodeMA850Battery type/life1 x 9V / 150 hoursEnvironment…

Milwaukee Instruments Mi805 Portable 4-in-1 Meter,pH/EC/TDS/Temp, Range: 0.00 TO 14.00 pH, 0 to 3999 uS/cm ED, 0 to 1999 ppm TDS, 0.0 to 60.0°C / 32.0 to 140.0°F Temp

$646.38

Multi-range pH/EC/TDS and Temperature Meter- 4-in-1 pH/EC/TDS/Temperature probe- The rugged MA851D/1 probe has been designed for heavy-duty applications (agriculture, industrial, etc.) Range0.00 – 14.00 pH 0 – 3999 µS/cm 0 – 1999 ppm 0.0 – 60.0°C 32.0 – 140.0°FResolution0.01 pH 1 µS/cm 1 ppm 0.1°C 0.1°FAccuracy± 0.01 pH ± 2% Full scale (for EC and TDS) ± 0.5°C ± 1°FTypical EMC Deviatio…

How to Select and Install a Home Well Water Chlorinator

Common household bleach can used in an automatic chlorinator system to kill coliform bacteria and provide disinfected water. In some wells iron or sulfur bacteria can create ‘rotten egg’ odors and cause staining of fixtures and appliances. Chlorinators can also be used to address these problems.

The first step in selecting a chlorinator is to find out your basic water chemistry and have your well water tested. A general mineral analysis will provide a list of the common minerals (calcium, magnesium, iron, manganese, Dissolved Solids) alkalinity and pH. The pH is important because the higher the pH the more chlorine is required.

How Much Chlorine Should I Plan to Add?

Chlorine is injected in parts per million (’ppm’) which is the same as saying milligrams per liter (’mg/L’). For bacteria you want 1 to 2 ppm of chlorine and approximately 10 minutes of contact time. If the water is colder than 50F you may need longer contact time.

For each part per million of iron or manganese you want to inject 1 ppm of chlorine. For each 1.0 ppm of hydrogen sulfide gas (which causes the rotten egg smell in water) you want to inject 2 to 3 ppm of chlorine.

So say you have bacteria and 2.0 ppm of iron. For our example here, we will assume you want to inject 3 ppm of chlorine.

How Do I Know What Size Chlorinator Pump to Install?

The next step in selecting your metering pump is to know how many gallons per minute your well water is flowing at the point where you will be injecting the chlorine. Usually the best place to inject the chlorine is before the Pressure Tank. Unless you have a variable-speed pump, your water at this point is flowing in approximately the same flow rate every time the well pump turns on. After you use up your reserve in your pressure tank, the pressure switch turns on the well pump and the water begins to flow from the well.

You can easily calculate the flow rate at this point by following these steps:

1. Open any hose bib or faucet until pump turns on.
2. Close hose bib or faucet and let pump fill up pressure tank until it turns off.
3. Using a 1 or 5 gal. bucket, open faucet, collect and measure all water discharged until pump turns on. Let us say this amount is 20 gallons.
4. When pump turns on, immediately close faucet and start timing pump cycle.
5. When pump turns off, record pump cycle time to refill pressure tank in seconds. Let us say this figure is two minutes or 120 seconds.
6. Divide the number of gallons collected in Step 3 by the number of seconds in Step 5. 20 divided by 120 is 0.166
7. Multiply the answer from Step 6 by 60, which comes out to 10.
8. The answer in Step 7 is the average pumping capacity of the pump in gallons per minute (GPM).

Now that you know the amount of chlorine you want to install (3 ppm) and the flow rate of the water stream you are injecting the chlorine into (10 gallons per minute) you are finally ready to calculate the size of the metering pump!

How Strong Should the Chlorine Bleach Solution Be?

Use unscented 5% chlorine laundry bleach and dilute it by adding 9 gallons of water to 1 gallon of bleach. This will give you a solution strength of 5000 parts per million of chlorine.

Metering Pump Sizing

Metering pumps are often rated in the amount of chlorine solution they can pump by gallons per day. They have adjusting knobs so you can pump the full output or turn the pump down to deliver up 90% less than the output.

The formula simple: multiply the flow water (GPM) times the Applied Dosage in Parts Per Million and them multiply this by 1440 (the number of minutes in on 24 hour period). Finally divide this number by the solution strength being used.

10 GPM x 3.0 PPM x 1440 divided by 5000 = 8.6 Gallons Per Day

At this rate you can select a metering pump that can pump 10 gallons per day and adjust the output of the pump to 86% to achieve the desired 8.6 gallons per day. Finally you can test the chlorine residual at the kitchen sink. Your goal should be to have a residual of 0.2 to 0.8 ppm of chlorine. If you find the residual is too high, you can adjust the metering pump down to deliver less or dilute the chlorine solution with more water. If you find the residual is too low, you can make the solution strength stronger by using less water to dilute the solution, or you can turn up the output of the metering pump.

Mika Miko – We Be Xuxa [5/5]

$13.82

Disc 1:Blues Not SpeedTurkey SandwichWildboreSexTotionOn The RiseBeat The RushJohnson R CoolSex JazzKeep On CallingTurky Barntard Mix

Alex Woodard – Alex Woodard [8/19] *

$11.98

Disc 1:OlderRenoTable, TheMountain TownHalfwayPhotographBeautiful NowHoopsBillie HolidayHeathen`s PrayerThere Is No More Time…

Preparing For The Project Management Professional Certification Exam(pmp

$19.57

This book explains the nature of project management, the methods for controlling time and cost set out in the Guide to the project management body of knowledge (PMBOK), and how all of the tools and techniques relate to one another. The third edition re…

Introduction to Computers and Applications A?

4. When shopping and comparing different printers, it is NOT that important to consider the cost of the replacement toner cartridges.

True
False

5. The print quality of the printer is determined by the DPI, or dots per inch.

True
False

6. The laser printer works by using a laser beam to “draw” the image or text on the paper.
True
False

7. The printer speed is measured in PPM. PPM is short for ______________.

Possible Printer Meter
Pages Per Minute
Printer Parameter Modulator
Pixels per Millimeter

8. Print quality is determined by how well the printer produces an image on a piece of paper.
True
False

9. USB is a popular technology that most modern printers use to connect the printer to the computer.
True
False

10. Though not widely used in most new computers today, the parallel port is still used in most older computers to connect to the printer.
True
False

F The grade you’ll get for not reading your textbook.